Cabinet Refacing Cost Per Door
TL;DR
Cabinet refacing cost per door runs $150–$400 each installed, or $100–$250 per linear foot — and the number on your quote is almost never just the door. It bundles the new door, the matching veneer on the frame, hinges, handles, and installation labor. Count every door and drawer front, multiply by the per-door price, then add veneer and hardware to estimate your kitchen. A typical 10×10 kitchen lands around $4,000–$6,000 before upgrades.
Cabinet refacing cost per door is the number every homeowner wants first — and the number most quotes hide inside a single lump sum. A contractor says “$7,500 for the kitchen” and you have no way to tell whether that is fair, padded, or a bargain. Per-door pricing fixes that. Once you know what one opening should cost, you can count your own kitchen, do the multiplication yourself, and spot a bad quote before you sign anything. This guide breaks down the per-door price, explains the per-linear-foot price alongside it, and works a full 10×10 example so you can estimate your own kitchen in ten minutes.
How Much Does Cabinet Refacing Cost Per Door?
Cabinet refacing cost per door is $150–$400 per opening installed, with most kitchens landing in the $200–$300 middle of that range. A standard Shaker door in laminate sits near the low end; a custom solid-wood door with a premium veneer sits near the high end. Drawer fronts usually cost a little less than full doors, roughly $100–$250 each.
That range is the planning figure for a professionally installed job — door, veneer, hinges, handles, and labor bundled together. Installation is the biggest single cost: labor runs 50–70% of a refacing total. Published guides show the same spread: one national guide averages $435 per door installed, while a refacing company prices $250–$450 per door with everything included. Treat the band as a starting point and compare three itemized quotes. If a quote comes in above $400 per door, ask for the line items — something specific (custom sizes, premium veneer, glass inserts) should explain it.

| Door type | Per-door price installed | Best for |
|---|---|---|
| Laminate Shaker door | $150–$220 | Budget refresh, rental kitchens, clean modern look |
| Thermofoil (RTF) door | $180–$280 | Smooth painted look, easy cleaning, mid-range budgets |
| Wood veneer door | $250–$350 | Real wood grain, stainable, best long-term value |
| Solid wood door | $300–$400 | Premium kitchens, paintable and refinishable, longest life |
| Drawer front (any material) | $100–$250 | Usually priced lower than a full door of the same material |
| Glass-insert door | $300–$400+ | Display cabinets, open feel — glass and framing add cost |
All prices are rough planning estimates, not quotes — material, door size, and local labor rates move them up or down.
How Much Does Cabinet Refacing Cost Per Linear Foot?
Per-linear-foot pricing runs $100–$250 for most kitchens, or $90–$455 by material from budget laminate to premium wood veneer. The linear foot measures the width of wall your cabinets cover, not the number of doors — so it is the faster way to sanity-check a whole-kitchen quote.
The two pricing methods measure different things, and contractors switch between them depending on what flatters their quote. Per-door pricing counts openings: every door and drawer front is one unit. Per-linear-foot pricing measures run length: a 10-foot wall of cabinets is 10 linear feet whether it holds six doors or twelve. That is why the two numbers rarely agree neatly — a kitchen with many small doors costs more per linear foot than a kitchen with a few wide ones. Use per-door pricing when your kitchen has an unusual number of openings (lots of small drawers, a pantry wall of narrow doors), and per-linear-foot pricing when you want a fast whole-kitchen estimate from a single measurement. The full breakdown of what a fair reface costs by size, material, and region is in the kitchen cabinet refacing cost guide.

| Material | Per linear foot installed | Per-door equivalent |
|---|---|---|
| Laminate | $90–$150 | $150–$220 |
| Rigid thermofoil (RTF) | $100–$250 | $180–$280 |
| Wood veneer | $100–$300 | $250–$350 |
| Solid wood doors + veneer box | $200–$455 | $300–$400 |
All prices are rough planning estimates, not quotes — get an itemized quote for your exact kitchen before deciding.
What Is Included in the Per-Door Price?
The per-door price includes the new door, the matching veneer on the exposed frame, new hinges, new handles, and installation labor. That bundle is the single most important thing to understand about refacing quotes — and the reason a “cheap per-door price” can still produce an expensive job.
Here is what each piece means. The door is the new slab — Shaker, flat-panel, or raised-panel — built to fit your existing box. The veneer is a thin skin, matched to the door’s species and finish, glued over the face frames and end panels so the old boxes disappear. Hinges are almost always new soft-close hinges, handles are new pulls or knobs, and labor covers removal, frame prep, veneer application, hanging, and adjustment. A quote that lists only “doors: $90 each” and leaves veneer, hinges, and labor as separate lines is not cheaper — it is just itemized differently. When you compare quotes, compare the same bundle: door + veneer + hinges + handles + labor, per opening. One national cost guide puts doors-only material at $50–$90 per door and drawer fronts at $30–$50 — useful if you are buying materials yourself, but not comparable to an installed per-door price.
How Do You Calculate Your Total Refacing Cost?
Count every door and drawer front, multiply by the per-door price, then add the linear-foot veneer charge and hardware. That is the whole calculation — and doing it yourself before the estimator arrives is the best protection against an inflated quote.
Walk the kitchen with a notepad and count every opening: each door is one, each drawer front is one, and each false front (the decorative panel in front of a sink) counts too, because it gets a new veneer face. A typical kitchen has 20–40 openings; count yours, do not guess. Multiply your count by the per-door price for your chosen material — use $200–$300 per opening as a mid-range planning figure. Then check the veneer: most quotes fold frame veneer into the per-door price, but some charge it separately at $8–$20 per linear foot of exposed frame. Finally, add hardware if it is not included: hinges and pulls run about $5–$25 per set. The calculator table below does the math for three kitchen sizes.

| Kitchen size | Openings (doors + drawer fronts) | Linear feet | Mid-range estimate ($200–$300 per opening) |
|---|---|---|---|
| Small (8×10, galley) | 15–20 | 12–16 | $3,000–$6,000 |
| Typical (10×10) | 20–30 | 18–22 | $4,000–$6,000 |
| Large (12×14, island) | 30–45 | 25–35 | $6,000–$9,500 |
All prices are rough planning estimates, not quotes — your count and your material choice set the real total.
Why Do Some Kitchens Cost More Per Door?
Custom sizes, premium veneer, glass inserts, and soft-close hardware push the per-door price up — and so do damaged boxes, awkward layouts, and big-city labor rates. Four cost drivers explain almost every quote that lands above the $150–$400 band.
First, size: standard doors are cheap because they are cut in batches; an oversized pantry door or a non-standard width is a one-off fabrication, and one-offs cost more. Second, material: solid wood and premium wood veneer cost more than laminate at every step — the door, the matching veneer, and the finish. Third, extras: glass inserts add framing and glazing labor, soft-close hinges cost more than standard hinges, and specialty finishes (glaze, distressing, two-tone) add a finishing pass. Fourth, condition and location: boxes needing repair before veneering add prep labor, and big-city contractors typically charge 20–30% more than small-town ones. If your quote is high, ask which of these four is driving it — a good estimator can point to the exact line.
Is Per-Door or Per-Linear-Foot Pricing Better for You?
Per-door pricing suits small kitchens with few doors; per-linear-foot pricing suits long runs of standard cabinets. The right method is whichever one matches how your kitchen is actually built.
Choose per-door pricing when your kitchen has an unusual opening count — a small galley with only 12 openings, a wall of narrow pantry doors, or a layout heavy on drawers. There, linear-foot pricing undercounts the work, because every opening must be fabricated, hung, and adjusted. Choose per-linear-foot pricing when your kitchen is a long, standard run — a straight 12-foot wall of base and wall cabinets with normal-width doors. There, counting feet is faster and the per-foot rate is the number contractors actually use to build the quote. Either way, ask the estimator to show you both numbers: a quote that looks fair per door but steep per linear foot (or the reverse) is telling you something about where the margin sits. And if you are still deciding between refacing and starting over, the cabinet refacing vs replacement comparison prices both options side by side.
How Can You Lower Your Cabinet Refacing Cost?
Choose laminate, keep standard door sizes, reuse hardware, and get three quotes. Those four moves together can cut 20–30% off a typical refacing bill without touching quality where it matters.
Laminate is the biggest single saving: a laminate reface on a full kitchen runs $1,000–$3,000 in materials, against $2,500–$6,000 for wood veneer, and modern laminate looks far better than the peel-and-stick of a decade ago. Standard door sizes are the second saving — every custom-width door is a surcharge, so keep your existing openings and let the new doors fit them. Reusing hardware is the third: if your hinges and pulls are in good shape and the finish still suits the new doors, keep them and save $5–$25 per opening. And three quotes are the fourth: the spread between the highest and lowest itemized quote for the same job is routinely 20% or more, and the lowest is not always the worst — sometimes it is simply the contractor with the leanest overhead. One caution: never skip the veneer on exposed end panels. Unveneered ends are the tell-tale sign of a cheap reface, and the first thing a buyer notices.

How Much Will Your 10×10 Kitchen Cost? A Worked Example
A 10×10 kitchen with 20 openings at $200–$300 per door lands around $4,000–$6,000 before upgrades. Here is the full worked example, line by line, so you can swap in your own numbers.
Take a standard 10×10 kitchen: 14 doors and 6 drawer fronts, 20 openings total, about 20 linear feet of cabinets. At $250 per opening (mid-range thermofoil), the doors and drawer fronts come to $5,000. Frame veneer is included in that per-opening price in most quotes; if yours charges it separately, add roughly $8–$20 per linear foot of exposed frame, about $160–$400. New soft-close hinges and pulls, if not included, add about $5–$25 per opening, or $100–$500. Total: $5,000–$5,900 with everything bundled, or $4,000 at the low end with laminate doors at $200 per opening. For comparison, the same kitchen in solid wood at $350–$400 per opening lands at $7,000–$8,000, and a full replacement starts at $15,000. That gap is the whole case for refacing. Before you sign, run the same math on your own count, then check the quote against the online cabinet refacing quote checklist so you compare three estimates line by line instead of total against total.

Frequently Asked Questions
How much does refacing cost per door?
Refacing runs $150–$400 per opening installed, with most kitchens landing at $200–$300 per opening. The price bundles the new door, matching frame veneer, hinges, handles, and labor. Doors-only material without installation runs much lower, about $50–$90 per door — which is why you should always compare installed prices against installed prices.
Is it cheaper to reface by the door or by the linear foot?
Neither is inherently cheaper — they measure different things. Per-door pricing counts openings; per-linear-foot pricing ($100–$250) measures wall length. Per-door pricing is fairer for kitchens with many small openings; per-linear-foot pricing is faster for long standard runs. Ask your estimator to show both numbers and compare them.
How many doors does a typical kitchen have?
A typical kitchen has 20–40 openings — doors plus drawer fronts. A small galley has 15–20, a standard 10×10 has 20–30, and a large kitchen with an island has 30–45. Count every opening including false fronts before you get quotes, because the count is what the price is built on.
Does the per-door price include hardware?
Usually yes for a full installed quote: new soft-close hinges and new pulls or knobs are part of the per-door bundle in most professional quotes. If a quote lists hardware separately, add about $5–$25 per opening. Reusing your existing hardware in good condition is one of the easiest ways to save.
Why is one quote $4,000 and another $9,000 for the same kitchen?
Material, door style, and what is bundled. A $4,000 quote is usually laminate doors with standard sizes and hardware included; a $9,000 quote is usually solid wood or premium veneer with custom sizes, glass inserts, and soft-close everything. Compare the line items, not the totals — and get a third quote before deciding.
Should I reface or replace if my quote is over $13,000?
Get a replacement quote first. Once a refacing quote climbs past $13,000–$16,000, brand-new semi-custom cabinets often cost the same — and replacement buys you new boxes, a new layout, and a full warranty. Refacing only wins when it stays well below replacement money for the same kitchen.
Final Thought
Cabinet refacing cost per door is $150–$400 each, and the number only helps you if you know what it includes: door, veneer, hinges, handles, and labor, all bundled per opening. Count your openings, multiply by your material’s per-door price, and you can estimate your kitchen before any estimator walks in — a 10×10 at $200–$300 per opening is $4,000–$6,000, and anything far above that needs a specific reason. Get three itemized quotes, compare them line by line, and refuse any price that only survives until tonight. For the full picture of what a fair reface costs by size, material, and region, the kitchen cabinet refacing cost guide has the complete breakdown.